My Web Stats

All Applications

  • Bicycle & Motorcycle Chains
  • Drawer Runners
  • Electrical Circuit Board Exterior protection
  • Garage Door Tracks/Rollers and springs
  • Gardening Tools and Equipment
  • Gate Latches and Hinges
  • Hand and Electric Motor Mowers
  • Hedge Trimmers & Clippers
  • Inside Window Tracks
  • Metal Tool Boxes
  • Metal Garden Shed doors, sliding doors
  • Outside Air Conditioning Units
  • Playground Equipment
  • Quick release spray for nuts bolts and screws etc
  • Ride on Mowers
  • Sash Window Channels
  • Stops Squeaks
  • Trailer Gate Hinges
  • Under Bed-liner of trucks
  • Underneath Lawnmower Bodies

 

LANTOS Coatings is a light lanolin based rust inhibitors guards against corrosion on all metal surfaces. It eliminates moisture containing salt, dirt and other pollutants from metals, providing long-lasting protection for all around the home applications. It's natural lanolin based lubricant is safe for your family to use, is non-toxic, non-hazardous and 100% environmentally friendly. 

The secret is in the base product - lanolin - which has been used for centuries for its powerful anti-corrosive, anti-seize and lubricating qualities.

From interior service locks and hinges to outdoor lawn and garden equipment to the garage with numerous applications for vehicles and tools, even lubricating garage door runners, and springs, to bicycle chains, squeaking doors, drawer runners and many other....: Penetrates, Protects, Preserves all household interior and exterior needs.


Quick Release Lubricant

Lanolube LL730 acts as a quick release lubricant for "locked" or rusted screws and fittings. Its a natural replacement for (WD40).  Apply a small amount and leave to absorb into jammed fittings. Eases release and provides protection against future "jamming".

FEATURES

  • Acid, Alkali & Salt resistant
  • Class, Non-Hazardous
  • Di-electric properties to 70kV
  • Food Grade approved
  • Super Low Eco-Toxic
  • 100% Eco-Friendly
  • Safe to use, store and dispose

 

 

 

Bicycle & Motorcycle Chains

Use Lanolube LL730 to lubricate chains, bottom brackets, derailleur, hubs, seat posts, nuts and bolts, gears, levers, and brake cables.

  • Protects and reduces frictional wear of the pins, bushings rollers and link plates.
  • It cushions impact loads as the link assembly contacts the sprocket.
  • It dissipates fractional heat created during operation.
  • It assists in flushing away foreign materials on the rollers.
  • It creates a virtual fluid seal between the link pin bushing and rollers.
  • It helps retard oxidisation.

Tip: Spray on a light coat, then wipe off the excess.

Use:: Lanolin Grease LG100 for assembly of parts.

Product Brochure 2018 - Click here

Product Brochure "Bicycles" - Click here

Visit the technical page for additional support material, SDS and technical data



Garage Door Runners/ Hinges/ Locks

Lantos LanolubeLL730 can last up to 12 months for indoor applications. Do not over apply - a small amount is all that is necessary. Acts as a general lubricant that does not evaporate or breakdown in the short term. Natures answer to every squeak and protection from corrosion.

For garage door lubrication.

  • Tracks. Start by cleaning the tracks with a rag to eliminate any build-up that might be interfering with your doors gentle glide. Don't lubricate the tracks, but ensuring they are clean is essential to your doors functioning.
  • Springs. Lightly spray down the garage door springs that lift your garage.
  • Hinges. Lubricate steel hinges at their pivot points.
  • Rollers. If your rollers have nylon wheels that make contact with the track, make sure to only lubricate the bearings.
  • Locks. If your key sticks or the lock is hard to open and close, give it a good shot of lubricant. Once you have all your garage door parts properly lubricated, lift it and close it several times to even out the lubricants distribution. If you still hear a lot of noise coming from your door, follow that sound to determine if you simply missed a moving part or if more substantial correction is required.


Tools (Maintenance Protection)

For tools stored in the garage, Lantos Lanolube LL730 keeps metals from corroding due to moisture and humidity. Spray directly onto the tool, or onto a rag and rub in.

For the protection of the saw table surface;

First, remove the rust. Scour the surface with mineral spirits and synthetic steel wool or 400-grit wet-or-dry sandpaper. Wipe off the surface with a clean cloth, and repeat as necessary.

Using the shop vac, a paintbrush and a rag, remove all of the dust/sawdust off the machine. Use LG100 for all nuts/bolts as a natural anti-seize.

When prepared, spray a light covering of Lanolube LL730 over the surface, allow to dry and then store.